1Z0-877 | The Up to the immediate present Guide To 1Z0-877 exam
Q31. Click the Exhibit button.
You have a system with a single disk drive. You need to add a new 6GB file system for /data and can only add it on this disk. Given the information displayed in the exhibit, which describes the option for adding a 6GB slice to this disk without destroying any existing data on the disk or reloading the operating system?
A. Increase slice 4 to 6GB.
B. Combine slices 4 and 5.
C. Reduce the slice 7 to 1GB. Change slice 4 to 6GB.
D. Not enough contiguous space on the disk to make a new 6 GB file system.
E. All of your slices are used. You cannot add a new slice for the /data file system without repartitioning and reloading the OS.
Answer: A
Q32. An administrator uses a file system snapshot to back up a partition that contains user data. While the backup is in progress, the file system used for the backing store runs out of space.
What are the consequences?
A. The backup progresses, but processes updating the data to be backed up are suspended until there is more space available for the snapshot.
B. The backup is suspended until there is more space available for the snapshot.
C. The backup progresses without incident.
D. The backup is aborted and the snapshot is deleted.
Answer: D
Q33. When your Solaris system is booted, a startup script initializes the rpcbind service. Which script is it?
A. /lib/svc/method/net-physical
B. /etc/rcS.d/S30network
C. svc:/network/rpc/bind:default
D. /lib/svc/method/rpc-bind
Answer: D
Q34. As system administrator, you are asked to remove the SUNWaudd package from a user's workstation. When you run the command to remove this package, you see the following messages on your console:
What happens to the files associated with the SUNWauddx and SUNWusb packages if you continue with the removal operation?
A. The files are removed.
B. The files remain on the system.
C. Only the files shared with the SUNWaudd package are removed.
D. The files are marked for removal, but are only removed after the next reboot.
Answer: B
Q35. According to company policy, all installations must be done over the network, and network installations must be done using a secure protocol.
Which installation method must you use?
A. the Solaris Live Upgrade method using the lu command and a spare disk drive
B. a WANboot installation
C. a JumpStart installation
D. a Flash Archive installation
Answer: B
Q36. You want to boot a SPARC-based system and stop system initialization at run level 2. Which two procedures can do this? (Choose two.)
A. Use the reboot -- -2 command to shut down and reboot the system.
B. From the OBP ok prompt, boot the system using the boot -2 command.
C. Set the milestone for this reboot to multi-user.
D. Shut down the system with the init s command, then use the init 2 command to switch to run level 2.
E. From the OBP ok prompt, boot the system to run level s, then use the init command to set the run level to 2.
Answer: C,E
Q37. You are asked to perform a Solaris OS installation on a workstation. One requirement is that if the root file system becomes corrupted, the recovery of the root slice must take the minimum amount of time.
Which layout will take the least time to recover the root slice (/)?
A. / 71.5 gigabyte swap512 megabyte
B. /20 gigabyte swap1024 megabyte /usr10 gigabyte /export/home41 gigabyte
C. /10 gigabyte swap1024 megabyte /var10 gigabyte /usr30 gigabyte /export/home21 gigabyte
D. /40 gigabyte swap1024 gigabyte /usr10 gigabyte
Answer: C
Q38. When your Solaris system is booted, a startup script initializes the rpcbind service. Which script is it?
A. /lib/svc/method/net-physical
B. /etc/rcS.d/S30network
C. svc:/network/rpc/bind:default
D. /lib/svc/method/rpc-bind
Answer: D
Q39. You have completed the installation of the OS and you want to confirm what has been installed on the system. Where is the log file of the installation process stored?
A. /var/adm/messages
B. /var/install/contents
C. /var/sadm/logs/install_data_logs
D. /var/sadm/install_data/install_log
Answer: D
Q40. At boot up, this service calls the startup scripts which are used to configure each network interface with an IP address and other required network information. Which service is it?
A. svc:/network/service:default
B. svc:/network/physical:default
C. svc:/network/ifconfig:default
D. svc:/network/inetd:default
Answer: B