300-410 | Highest Quality Cisco 300-410 Preparation Online

NEW QUESTION 1
Refer to the exhibit.

Network operations cannot read or write any configuration on the device with this
configuration from the operations subnet. Which two configurations fix the issue? (Choose two.)

• A. Configure SNMP rw permission in addition to community ciscotest.
• B. Modify access list 1 and allow operations subnet in the access list.
• C. Modify access list 1 and allow SNMP in the access list.
• D. Configure SNMP rw permission in addition to version 1.
• E. Configure SNMP rw permission in addition to community ciscotest 1.

Answer: AB

NEW QUESTION 2
Refer to the exhibit.

An administrator that is connected to the console does not see debug messages when
remote users log in. Which action ensures that debug messages are displayed for remote logins?

• A. Enter the transport input ssh configuration command.
• B. Enter the terminal monitor exec command.
• C. Enter the logging console debugging configuration command.
• D. Enter the aaa new-model configuration command.

Answer: B

NEW QUESTION 3
Refer to the exhibit.

Users in the branch network of 2001:db8:0:4::/64 report that they cannot access the Internet. Which command is issued in IPv6 router EIGRP 100 configuration mode to solve this issue?

• A. Issue the eigrp stub command on R1.
• B. Issue the no eigrp stub command on R1.
• C. Issue the eigrp stub command on R2.
• D. Issue the no eigrp stub command on R2.

Answer: A

NEW QUESTION 4
While troubleshooting connectivity issues to a router, these details are noticed:
Standard pings to all router interfaces, including loopbacks, are successful.
Data traffic is unaffected.
SNMP connectivity is intermittent.
SSH is either slow or disconnects frequently.
Which command must be configured first to troubleshoot this issue?

• A. show policy-map control-plane
• B. show policy-map
• C. show interface | inc drop
• D. show ip route

Answer: A

NEW QUESTION 5
An engineer is trying to copy an IOS file from one router to another router by using TFTP. Which two actions are needed to allow the file to copy? (Choose two.)

• A. Copy the file to the destination router with the copy tftp: flash: command
• B. Enable the TFTP server on the source router with the tftp-server flash: <filename> command
• C. TFTP is not supported in recent IOS versions, so an alternative method must be used
• D. Configure a user on the source router with the username tftp password tftp command
• E. Configure the TFTP authentication on the source router with the tftp-server authentication local command

Answer: AB

NEW QUESTION 6
Refer to the exhibit.

What is the result of applying this configuration?

• A. The router can form BGP neighborships with any other device.
• B. The router cannot form BGP neighborships with any other device.
• C. The router cannot form BGP neighborships with any device that is matched by the access list named “BGP”.
• D. The router can form BGP neighborships with any device that is matched by the access list named “BGP”.

Answer: D

NEW QUESTION 7
Which statement about IPv6 ND inspection is true?

• A. It learns and secures bindings for stateless autoconfiguration addresses in Layer 3 neighbor tables.
• B. It learns and secures bindings for stateless autoconfiguration addresses in Layer 2 neighbor tables.
• C. It learns and secures bindings for stateful autoconfiguration addresses in Layer 3 neighbor tables.
• D. It learns and secures bindings for stateful autoconfiguration addresses in Layer 2 neighbor tables.

Answer: B

NEW QUESTION 8
Refer to the exhibit.

Which configuration configures a policy on R1 to forward any traffic that is sourced from the 192.168.130.0/24 network to R2?

• A. Option A
• B. Option B
• C. Option C
• D. Option D

Answer: D

NEW QUESTION 9
R2 has a locally originated prefix 192.168.130.0/24 and has these configurations:

What is the result when the route-map OUT command is applied toward an eBGP neighbor R1 (1.1.1.1) by using the neighbor 1.1.1.1 route-map OUT out command?

• A. R1 sees 192.168.130.0/24 as two AS hops away instead of one AS hop away.
• B. R1 does not accept any routes other than 192.168.130.0/24
• C. R1 does not forward traffic that is destined for 192.168.30.0/24
• D. Network 192.168.130.0/24 is not allowed in the R1 table

Answer: A

NEW QUESTION 10
Refer to the exhibit.

Which statement about R1 is true?

• A. OSPF redistributes RIP routes only if they have a tag of one.
• B. RIP learned routes are distributed to OSPF with a tag value of one.
• C. R1 adds one to the metric for RIP learned routes before redistributing to OSPF.
• D. RIP routes are redistributed to OSPF without any changes.

Answer: B

NEW QUESTION 11
Refer to the exhibit.

A router receiving BGP routing updates from multiple neighbors for routers in AS 690. What is the reason that the router still sends traffic that is destined to AS 690 to a neighbor other than 10.222.1.1?

• A. The local preference value in another neighbor statement is higher than 250.
• B. The local preference value should be set to the same value as the weight in the route map.
• C. The route map is applied in the wrong direction.
• D. The weight value in another statement is higher than 200.

Answer: D

NEW QUESTION 12
Which configuration adds an IPv4 interface to an OSPFv3 process in OSPFv3 address family configuration?

• A. router ospfv3 1address-family ipv4
• B. Router(config-router)#ospfv3 1 ipv4 area 0
• C. Router(config-if)#ospfv3 1 ipv4 area 0
• D. router ospfv3 1address-family ipv4 unicast

Answer: B

NEW QUESTION 13
An engineer configured the wrong default gateway for the Cisco DNA Center enterprise interface during the install. Which command must the engineer run to correct the configuration?

• A. sudo maglev-config update
• B. sudo maglev install config update
• C. sudo maglev reinstall
• D. sudo update config install

Answer: A

NEW QUESTION 14
Refer to the exhibit.

Which subnet is redistributed from EIGRP to OSPF routing protocols?

• A. 10.2.2.0/24
• B. 10.1.4.0/26
• C. 10.1.2.0/24
• D. 10.2.3.0/26

Answer: A

NEW QUESTION 15
Refer to the exhibit.

An engineer is trying to connect to a device with SSH but cannot connect. The engineer connects by using the console and finds the displayed output when troubleshooting. Which command must be used in configuration mode to enable SSH on the device?

• A. no ip ssh disable
• B. ip ssh enable
• C. ip ssh version 2
• D. crypto key generate rsa

Answer: D

NEW QUESTION 16
Which transport layer protocol is used to form LDP sessions?

• A. UDP
• B. SCTP
• C. TCP
• D. RDP

Answer: C

NEW QUESTION 17
When provisioning a device in Cisco DNA Center, the engineer sees the error message “Cannot select the device. Not compatible with template”.
What is the reason for the error?

• A. The template has an incorrect configuration.
• B. The software version of the template is different from the software version of the device.
• C. The changes to the template were not committed.
• D. The tag that was used to filter the templates does not match the device tag.

Answer: B

NEW QUESTION 18
Refer to the exhibit.

An engineer is trying to generate a summary route in OSPF for network 10.0.0.0/8, but the summary route does not show up in the routing table. Why is the summary route missing?

• A. The summary-address command is used only for summarizing prefixes between areas.
• B. The summary route is visible only in the OSPF database, not in the routing table.
• C. There is no route for a subnet inside 10.0.0.0/8, so the summary route is not generated.
• D. The summary route is not visible on this router, but it is visible on other OSPF routers in the same area.

Answer: A

NEW QUESTION 19
Refer to the exhibit.

An engineer is trying to redistribute OSPF to BGP, but not all of the routes are redistributed. What is the reason for this issue?

• A. By default, only internal routes and external type 1 routes are redistributed into BGP
• B. Only classful networks are redistributed from OSPF to BGP
• C. BGP convergence is slow, so the route will eventually be present in the BGP table
• D. By default, only internal OSPF routes are redistributed into BGP

Answer: A

NEW QUESTION 20
Refer to the exhibit.

Why is user authentication being rejected?

• A. The TACACS+ server expects “user”, but the NT client sends “domain/user”.
• B. The TACACS+ server refuses the user because the user is set up for CHAP.
• C. The TACACS+ server is down, and the user is in the local database.
• D. The TACACS+ server is down, and the user is not in the local database.

Answer: D

NEW QUESTION 21
Refer to the exhibit.

An IP SLA was configured on router R1 that allows the default route to be modified in the event that Fa0/0 loses reachability with the router R3 Fa0/0 interface. The route has changed to flow through
router R2. Which debug command is used to troubleshoot this issue?

• A. debug ip flow
• B. debug ip sla error
• C. debug ip routing
• D. debug ip packet

Answer: C

NEW QUESTION 22
Drag and drop the OSPF adjacency states from the left onto the correct descriptions on the right.

• A. Mastered
• B. Not Mastered

Answer: A

Explanation:

NEW QUESTION 23
Which statement about MPLS LDP router ID is true?

• A. If not configured, the operational physical interface is chosen as the router ID even if a loopback is configured.
• B. The loopback with the highest IP address is selected as the router ID.
• C. The MPLS LDP router ID must match the IGP router ID.
• D. The force keyword changes the router ID to the specified address without causing any impact.

Answer: B

NEW QUESTION 24
......