1Z0-546 | Virtual Oracle 1Z0-546 dumps
Q11. What ACLs command would you use to stop the acslm process from accepting new requests?
A. idle
B. stop req all
C. q requests now
D. requests wait
Answer: A
Explanation: Use this procedure to suspend request processing by putting ACSLS in the idle state. Typically, this procedure is used before shutting down ACSLS, but you can also use it to temporarily stop ACSLS request processing. To idle ACSLS, do the following:
1. From a cmd_proc, enter the following command:
idle
ACSLS processes all current requests, rejects all new requests, and goes
into the idle state.
The following message appears when ACSLS request processing stops.
ACSLM Request Processing Stopped: Success.
Reference; StorageTek ACSLS, Automated Cartridge System Library Software Idling ACSLS
Q12. Which SL3000 configuration will in general provide the best performance?
A. Base CEM CEM CEM
B. CEM CEM CEM Base
C. CEM DEM Base CEM
D. CEM DEM CEM
Answer: A
Explanation: The below figure is an example of how the SL3000 uses CenterLine Technology to help balance the workload and improve performance.
Addressing and Panel Numbering
Reference: StorageTek SL3000 Modular Library System Customer Orientation Checklist
Q13. What ACSLS command is used to find out the status of all the tape drives in an LSM?
A. Query LSM 0 drive all
B. Query drive all
C. show drive all
D. Display drive all LSM 0
Answer: B
Explanation: To query all drives: query drive all
Note: Mount/dismount a cartridge to verify ACSLS:
1. Verify that you are logged in as acsss.
2. If ACSLS is not running, start it by entering rc.acsss
3. Query the server from the cmd_proc by entering query server
If messages are displayed indicating that the server is in recovery mode, wait for a message indicating that the server is running.
4. Verify that the at least one of the following are online. If not, bring them online with the vary command. query port all query acs all query lsm all query drive all
Q14. What are the correct steps for finding the screen to install a hardware activation file?
A. Log in to the SLC and go to Tools > Reports > Versions > Software Versions
B. Log in to the SLC and go to Tools > Hardware Activation > Install Hardware Activation Key
C. Log in to the SLC and go to Hardware Activation > Install Hardware Activation Keys
D. Log in to the SLC and go to Maintenance > Install Hardware Activation Keys
Answer: B
Explanation: Install a New Hardware Activation File on the Target Library
Use this procedure to install a new hardware activation file on the target library.
1.Use the SL Console to log in to the target library.
2. Select Tools > Hardware Activation, and click the Install Hardware Activation Keys tab.
Note:A hardware activation file can be delivered to you in the following ways:
* Via e-mail from Oracle Corporation
* Installed by your Oracle support representative
Reference: StorageTek SL3000 Modular Library System, User’s Guide, Install a New Hardware Activation File on the Target Library
Q15. In what manner should libraries be added to SL8500 for nondisruptive growth of a library complex?
A. from left to tight, when facing the front doors
B. from right to left, when facing the front doors
C. from either side, It does not matter
D. only from the left
Answer: B
Explanation: Adding SL8500 Libraries to theLeft
When you add libraries to the left of an existing library complex, you can dynamically upgrade the configuration of the software (ACSLS or HSC). This upgrade must be done to configure the LSMs, panels, cells, and tape drives in the new libraries.
Note: Capacity for the SL8500 uses Capacity on Demand and RealTime Growth to allow you to instantly increase and activate capacity without disruption.
Reference; StorageTek SL8500 Modular Library System, Best Practises,Adding SL8500 Libraries to theLeft
Q16. Which feature contributes most to improved performance and higher library availability with the SL8500?
A. Redundant Control Cards
B. Partitioning
C. Redundant CAPs
D. Redundant Robots
Answer: B
Explanation:
Q17. What is the correct procedure to enable ACSLS automatic backups?
A. Log in as "root" and issue the "db_command bkup" instruction B. Log in as "acsss" and run "bdb.acsss" with option #5
C. Log in as "acsss", idle ACSLS, Stop ACSLS, then issue acsss_config
D. Log in as "acsss", enter an "acsss_config", and select option #5
Answer: D
Explanation: Setting Automatic Backup Variables Option 5 allows you to set or change the following automatic backup variables:
. Prompt: Would you like to modify the automatic backup settings? ( y or n)
Variable: None. The automatic backup settings are saved in crontab.
Please use acsss_config to modify these settings.
Valid options are:
. Y - If yes, you are asked if you want to back up everyday. If “yes”, then
you must enter the time in HH:MM format.
If no, you must select the day(s) of the week to back up. Then you
must enter the time in HH:MM format.
. N - you go to the next question regarding the retention period of SDMmanaged database backup files.
Reference: StorageTek ACSLS, Automated Cartridge System Library Software, Setting Automatic Backup Variables
Q18. On the SL3000, if you convert two Cartridge Expansion Modules to two Parking Expansion Modules, how many slots will you lose?
A. 312
B. 440
C. 516
D. 620
Answer: D
Explanation: The optional Cartridge Expansion Module (CEM) provides additional storage cell capacity and growth for cartridges only.
Each CEM adds up to 620 data cartridge physical storage cells.
Note: The optional Parking Expansion Modules (PEMs) provide additional storage cell capacity and growth, as well as space for a redundant TallBot to be “parked.” The parking space makes the three outer-most columns of storage cells on the front and rear walls inaccessible. The inaccessible cells can be left out of the module, or they can be installed to allow later conversion of the PEM to a CEM. PEMs do not include tape drives.
PEMs are only used with the Dual Robotics feature, and they are always installed in pairs. They must be the last modules on the right and left sides of the library series.
Q19. Which action is not likely to improve the performance of the SL3000?
A. Implementing dual robots will usually give the biggest performance increase.
B. Configure your SL3000 as symmetrically as possible.
C. At dismount, always place the cartridge back in the storage cell it was moved from.
D. If you do not have a large number of drives, place them in alternating columns where possible
E. Try to place frequently used cartridges near the drives.
Answer: D
Explanation:
Reference: StorageTek SL3000 Modular Library System, User’s Guide
Q20. Which SL3000 feature does not require a hardware activation file?
A. Partitioning
B. Multiple CAPs
C. Dual TCPIP
D. Capacity
Answer: B
Explanation: The hardware activation utility allows you to activate selected optional features on the SL3000 library.
Reference: StorageTek SL3000 Modular Library System, User’s Guide