JN0-104 | What Exact JN0-104 Free Samples Is
It is impossible to pass Juniper JN0-104 exam without any help in the short term. Come to Pass4sure soon and find the most advanced, correct and guaranteed Juniper JN0-104 practice questions. You will get a surprising result by our Replace Junos - Associate (JNCIA-Junos) practice guides.
Also have JN0-104 free dumps questions for you:
NEW QUESTION 1
You recently uploaded a new software package to your Junos and you want to ensure that the file uploaded successfully by verifying the file size. In this scenario, which command should you use?
- A. file checksum shal
- B. file compare
- C. file list detail
- D. file show encoding
Answer: C
NEW QUESTION 2
What is the default firewall filter behavior when a term is matched but no terminating action is specified?
- A. an implicit deny and the filter evaluation terminates
- B. an implicit accept and the filter evaluation terminates
- C. an implicit accept and the filter evaluation continues to the next term
- D. an implicit deny and the filter evaluation continues to the next term
Answer: C
NEW QUESTION 3
Exhibit:
Refer to exhibit, What will be the result?
- A. The device will boot in a multi-user mode at the configuration prompt
- B. The device will boot in a Single-user mode at the operational prompt
- C. The device will boot in a multi-user mode at the shell prompt
- D. The device will boot in a Single-user mode at the shell prompt
Answer: A
NEW QUESTION 4
Which source of routing information is preferred by default?
- A. static
- B. RIP
- C. direct
- D. BGP
Answer: A
NEW QUESTION 5
Which command is used to validate the syntax of a configuration without applying the
configuration?
- A. commit check
- B. commit confirmed
- C. commit synchronize
- D. commit and-quit
Answer: A
NEW QUESTION 6
Which logical interface is able to forward IP traffic?
- A. Ge-0/0/0
- B. Ge-0/0/2
- C. Ge-0/0/2.0
- D. Ge-0/0/1.0
Answer: C
NEW QUESTION 7
You are in configuration mode at the top of the hierarchy. How would you save your configuration
to a file on the router?
- A. save configuration <filename>
- B. save config <filename>
- C. save <filename>
- D. save run <filename>
Answer: C
NEW QUESTION 8
You issue the request system zeroize command. Which statement is correct in this scenario?
- A. All data files are deleted and all configuration setting are returned to factory defaults.
- B. All data files remain unchanged but all configuration setting are returned to factory defaults.
- C. Disk space is freed by rotating log files and a proposed list of files to delete is presented.
- D. All data files are deleted and the configuration settings remain unchanged.
Answer: A
NEW QUESTION 9
You are connected to your Junos device using an SSH connection to the fxp0 interface. No other interface are currently configured beyond their default setting. You commit a configuration that makes the fxp0 interface unreachable from your management network. In this scenario, how would you re-establish communication with the device?
- A. Unplug the network cable and plug it back in.
- B. Power off and power on the device.
- C. Establish an SSH connection to the loopback interface.
- D. Connect to the console of the device.
Answer: D
NEW QUESTION 10
Which command is used to replace the current configuration?
- A. load replace
- B. load patch
- C. load override
- D. load set
Answer: C
NEW QUESTION 11
What is the network ID address of the IPv4 subnet that includes the IP address 114.180.192.120/28?
- A. 114.180.192.118/28
- B. 114.180.192.100/28
- C. 114.180.192.112/28
- D. 114.180.192.106/28
Answer: C
NEW QUESTION 12
Exhibit:
Referring to the exhibit, which statement is true?
- A. Traps are allowed from 10.21.15.180
- B. Traps are sent to 10.21.15.180
- C. Traps are sent to 10.21.15.16
- D. Traps are allowed from 10.21.15.16
Answer: D
NEW QUESTION 13
Which two methods keep a Junos device operational if the primary storage device fails? (Choose two.)
- A. Create a recovery snapshot.
- B. Enable the ephemeral database.
- C. Enable J-Web for device management.
- D. Create a rescue configuration.
Answer: AD
NEW QUESTION 14
Given the configuration shown below: set system authentication-order [tacplus] Which two statement are correct? (Choose two.)
- A. If the TACACS+ server is no available, the user is not allowed to access the device.
- B. If the TACACS+ server is no available, the local database is checked.
- C. If the TACACS+ server is available, and rejects the username/password provided, the local password database is checked.
- D. If the TACACS+ server is available, and rejects the username/password provided, the user is not allowed to access the device.
Answer: BD
NEW QUESTION 15
Click the Exhibit button.
Referring to the exhibit, if the router forwards traffic destined for 192.168.77.29, which next hop will be used?
- A. 10.10.1.2
- B. 10.10.11.2
- C. 10.10.0.2
- D. 10.10.20.2
Answer: C
NEW QUESTION 16
Which layer of the OSI model does a router use to make forwarding decisions?
- A. Layer 3
- B. Layer 4
- C. Layer 5
- D. Layer 2
Answer: A
NEW QUESTION 17
Which two commands will provide the current configuration of the MX1-PE1 BGP group on your router? (Choose two.)
- A. user@router# show groups | display set | match MX1-PE1
- B. user@router# show | display set | match MX1-PE1
- C. user@router> show configuration | match set | match MX1-PE1
- D. user@router> show configuration | dispalv set | match MX1-PE1
Answer: BD
NEW QUESTION 18
......
P.S. Surepassexam now are offering 100% pass ensure JN0-104 dumps! All JN0-104 exam questions have been updated with correct answers: https://www.surepassexam.com/JN0-104-exam-dumps.html (270 New Questions)