300-360 | Cisco 300-360 Braindumps 2021

NEW QUESTION 1
Which two options describe best practices that must be completed after a wireless installation is finished? (Choose two.)

• A. Make sure that there are no spaces between the devices on the rack that the Wireless Lan Controller is installed.
• B. Consult with the customer to ensure that the IT staff has a complete set of design and installation documents.
• C. Make sure the customer is aware that they should consider purchasing a support contract immediately after the installation is complete.
• D. Spend time with the customer to show them the controller GUI and inform them how they can reach the Cisco TAC if they have any problems.
• E. Test all the customer’s wireless devices and applications to ensure they are working properly.

Answer: BE

NEW QUESTION 2
Clients are experiencing artifacts in multicast video even though the network was recently upgraded to 802.11n APs. What three configuration changes will be most effective to improve performance? (Choose three.)

• A. increase mandatory data rate
• B. enable 40 MHz wide channels
• C. enable Call Admission Control
• D. increase QoS marking on multicast
• E. enable VideoStream
• F. disable Multicast Messaging

Answer: BCE

NEW QUESTION 3
Which description of the ideal VoWLAN design is true?

• A. smaller cells with all data rates enabled to ensure that all clients can associate
• B. larger cells with higher data rates enabled and WPA2 to secure voice conversations
• C. smaller cells with higher data rates enabled and admission control enabled through WMM
• D. smaller cells with higher data rates enabled and no overlap to prevent co-channel interference

Answer: C

NEW QUESTION 4
After installation of a new data-only wireless network, an engineer found that RRM has set all of the APs to a power level of 1.
Which option describes the reason for this?

• A. APs are too far apart for the set data rates.
• B. EORRM is enabled
• C. High co-channel interference exists.
• D. DTPC value is set too high.

Answer: A

NEW QUESTION 5
When designing a WLAN, AP placement is important. Which option describes how to rank the density of Aps needed to support location services versus data and voice services?

• A. Data services have the lowest density of APs compared to location services, which has the highest density.
• B. Data services have a lower density of APs compared to location services, but more than voice.
• C. Voice services have the highest density of APs over location and data services.
• D. Voice and data services require a higher density of APs than location services.

Answer: A

NEW QUESTION 6
An engineer is preparing for an active site survey of a hospital and is informed that he or she should not enter any active surgery suites.
Which option describes how the engineer should address this restriction?

• A. Conduct a passive wireless survey in the restricted areas.
• B. Use the predictive AP placement tool on the wireless controller
• C. Skip the area and estimate where to place the access points.
• D. Arrange to perform survey activities after hours.

Answer: A

Explanation: Passive Survey
Passive surveys are surveys that are performed with a listen-only mode. The survey client never associates to the access point (AP). Such surveys can be helpful when you look for rogue devices or you want a good gauge of downlink RF coverage from the infrastructure devices. These can be accomplished with a passive survey.

NEW QUESTION 7
Which piece of information gathered during a WLAN site survey should be included in the customer report?

• A. Analysis of server location and applications supported.
• B. Analysis of fiber-optic backbone infrastructure.
• C. Output from Cisco WCS Location Quality Inspector.
• D. Output from Cisco WCS VoWLAN Voice Readiness Tool.
• E. Output from Cisco WCS Planning Mode Tool.

Answer: E

NEW QUESTION 8
Which option is an enhancement of enabling WMM on an AP?

• A. All access classes use the same IEEE 802.11 sequence number.
• B. It disables U-APSD Power Save.
• C. Each access class has its own IEEE 802.11 sequence number.
• D. CAC is reserved for voice calls only.

Answer: C

NEW QUESTION 9
What protocol can be enabled to listen in on IPv4 multicast streams and maintain a map of what each client requests on a wireless LAN controller?

• A. IGMP
• B. MLD
• C. PAP
• D. ICMP
• E. SIP
• F. NTP

Answer: A

NEW QUESTION 10
A network engineer is retrofitting an existing building wired with Category 5e with AP 3800 and mGig switches.
Which cable length allows for 5G operation?

• A. 70 m
• B. 120 m
• C. 130 m
• D. 150 m

Answer: A

NEW QUESTION 11
A network installation on the site with ID 331372269 has been determined to be potentially hazardous to install. Which regulatory body must be consulted to ensure safety during the installation?

• A. FCC
• B. HIPPA
• C. PCI
• D. OSHA

Answer: D

NEW QUESTION 12
An engineer is determining powering requirements for a P2P wireless link using Cisco Aironet 1572EC access points.
Which power method is valid for the access point?

• A. 802.3af Power over Ethernet
• B. Power over Cable
• C. Cisco Inline Power
• D. 802.3at Power over Ethernet

Answer: B

NEW QUESTION 13
Refer to the exhibit.

Which type of cable connector is displayed that is used to connect antennas to transmitters?

• A. RP-TNC
• B. N
• C. SMA
• D. SMB
• E. MMCX

Answer: B

NEW QUESTION 14
A customer has dual-band devices that they want to use 40 MHz channels. If the customer is using Cisco 3600 Series access points with a 5508 controller. Which setting assists with this change?

• A. Enable band select globally.
• B. Enable aggressive load balancing.
• C. Disable lower data rates on 802 .11G GHz radios.
• D. Disable overlapping 802.11G channels.

Answer: A

NEW QUESTION 15
A wireless engineer is hired to design a network for six buildings with a WLC in each building to support the access points.
Which type of wireless architecture is being used?

• A. distributed deployment
• B. autonomous deployment
• C. unified deployment
• D. centralized deployment

Answer: D

NEW QUESTION 16
Which type of information should be included in an installation report?

• A. A complete characterization of the external WLAN environment.
• B. The exact number of users the WLAN will support.
• C. Soft copies of configuration for switches, routers, controllers, and location appliances.
• D. A detailed description of the WLAN environment during the post-installation testing, for example, number of people present, furniture, no furniture, and sources of interference present.

Answer: C