300-360 | Cisco 300-360 Dumps Questions 2021

NEW QUESTION 1
The AP has been configured property for a VoWLAN survey The RF environment contains a noise of -87 to -90 dBm. What is the target value for the cell edge reading?

• A. -62 dBm
• B. -67 dBm
• C. -60 dBm
• D. -70 dBm

Answer: B

NEW QUESTION 2
While evaluating a post-installation WLAN deployment, problems are occurring when a client roams from one AP to another. The client bounces back and forth between APs. Which two items can be checked to resolve this issue? (Choose two.)

• A. Check if the roaming settings in the AP are set properly for non-CCX clients
• B. Check the RF levels of the first AP as the client moves toward the second AP
• C. Check the client RSSI and SNR levels for both APs at the roaming point
• D. Simplify 802.1X/EAP by moving from external RADIUS to local authentication
• E. Check that the client roaming parameters are set properly

Answer: BC

NEW QUESTION 3
What is the optimal distance between APs for location services without considering the physical environment?

• A. 10 to 25 feet
• B. 90 to 120 feet
• C. 50 to 70 feet
• D. 80 to 100 feet

Answer: C

NEW QUESTION 4
A company has deployed a centralized wireless architecture in their headquarters. In this type of deployment, to which network layer do you recommend that the WLC connect?

• A. distribution layer
• B. Data center layer
• C. session layer
• D. access layer

Answer: A

NEW QUESTION 5
Which value does EDRRM AQ threshold Low represent?

• A. 20
• B. 25
• C. 30
• D. 35

Answer: D

NEW QUESTION 6
Which three WLC actions are needed to properly enable queuing with TSPEC for voice traffic?(choose three)

• A. configure WLAN platinum QoS
• B. configure WLAN gold QoS
• C. configure DTIM=2
• D. configure global 802.11b/g/n/ac,or both,to voice CAC
• E. configure WLAN setting to enable WMM.
• F. Configure WLAN Aironet information elements to enabled.

Answer: ADE

NEW QUESTION 7
An engineer is installing a wireless network in an industrial area with extreme temperatures and a significant amount of dust. Which enclosure should be used to protect the APs?

• A. ACU
• B. ADU
• C. NEMA
• D. WLSE

Answer: C

Explanation: Sometimes access points (APs) are located in areas where they are subject to extreme moisture,
temperatures, dust and particles. These APs might need to be mounted inside a sealed enclosure. The NEMA has a rating system for these enclosures, which are generally called NEMA enclosures.

NEW QUESTION 8
When a post-installation audit is performed with an auditing tool such as Ekahau, which three steps are associated with the passive portion of the audit? (Choose three.)

• A. Check that you have adequate signal levels as surveyed
• B. Make sure you emulate your customer client
• C. Check for co-channel interference
• D. Verify that the network traffic of physical data rate and packer loss meets user requirements
• E. Survey by SSID to ensure roaming is taking place
• F. Verify AP announced data rate coverage

Answer: ACF

NEW QUESTION 9
A customer requesting a site survey requires hidden APs, basic data coverage, and guest access in multifloor environment. Which industry vertical best describes this customer?

• A. manufacturing
• B. warehousing
• C. hospitality
• D. health care

Answer: C

NEW QUESTION 10
Which two basic characteristics would be needed from antennas used for survey and deployment in various indoor situations? (Choose two.)

• A. Horizontally polarized
• B. Vertically polarized
• C. Aesthetically fitting
• D. Least cost
• E. Highest gain
• F. Largest beamwidth

Answer: BC

NEW QUESTION 11
An engineer is assigned to assist a customer by estimating the number of access points needed to provide voice-grade wireless coverage in a carpeted office space. How many access points should be estimated to cover this space of roughly 38,000 square feet?

• A. 17
• B. 10
• C. 6
• D. 13

Answer: D

Explanation: The rule of thumb coverage plan is 1 AP per 5,000 square feet for data and 1 per 3,000 square feet for voice and location services.

NEW QUESTION 12
Which two steps are associated with the active portion of the audit when a post-installation audit is performed with an auditing tool such as Ekahau? (Choose two.)

• A. Check for co-channel interference by standing near an access point on one channel and watching for other access points that are on the same channel.
• B. Verify smooth roaming.
• C. Check to see if the signal level on other access points that are heard on the same channel is at least 19 dBm weaker than the access point that you are next to.
• D. Check that all channels are supported by the APs, regardless of client capabilities.
• E. Verify that the network traffic of physical data rate and packet loss meets user requirements.

Answer: BE

NEW QUESTION 13
An engineer is concerned with the compliance guidelines for human exposure to a rooftop RF transmitter that has been recently installed.
What regulation should be reviewed to ensure proper certification?

• A. OSHA 1910.97
• B. FCC QET Bulletin 65
• C. NFPS Article 810
• D. SCEE Section 28.1

Answer: B

Explanation: Evaluating Compliance with FCC Guidelines for Human Exposure to Radio Frequency Electromagnetic Fields;
This revised OET Bulletin 65 has been prepared https://www.fcc.gov/general/oet-bulletins-line

NEW QUESTION 14
You are planning the coverage for wireless VoIP by using Ekahau. Which signal strength does Ekahau recommend using for VoIP?

• A. -84 dBm
• B. -76 dBm
• C. -67 dBm
• D. -53 dBm

Answer: C

Explanation: Each vendor has their own recommended signal strength for a given data rate or application. For instance, one vendor may recommend designing their VoIP solution at -67 dBm (perhaps the most widely-used value for VoIP deployment if I had to choose one), while another may say -70 dBm. In most cases the values will differ only by a couple dB.
https://www.ekahau.com/blog/2015/01/13/ekahau-site-survey-heatmap-visualizations-part-2-signalstrength/

NEW QUESTION 15
An engineer wants the controller to report when a client exceeds the minimum acceptable RSSI level, to ensure support for the minimum data rate required.
Which controller option must be configured?

• A. Enable coverage hole detection
• B. Enable the coverage optional mode.
• C. Set the DCA channel sensitivity to high.
• D. Set the coverage exception level per AP to 0.

Answer: A

Explanation: If clients on a lightweight access point are detected at threshold levels (RSSI, failed client count, percentage of failed packets, and number of failed packets) lower than those specified in the RRM configuration, the access point sends a "coverage hole" alert to the controller. The alert indicates the existence of an area where clients are continually experiencing poor signal coverage, without having a viable access point to which to roam. The controller discriminates between coverage holes that can and cannot be corrected. For coverage holes that can be corrected, the controller mitigates the coverage hole by increasing the transmit power level for that specific access point. The controller does not mitigate coverage holes caused by clients that are unable to increase their transmit power or are statically set to a power level because increasing their downstream transmit power might increase interference in the
https://www.cisco.com/c/en/us/td/docs/ wireless/controller/7-0/configuration/ guide/c70/c70rrm.html

NEW QUESTION 16
Drag and drop the services on the left to the corresponding AP density levels on the right.

Answer:

Explanation: