300-360 | Guaranteed 300-360 Free Practice Questions 2021

NEW QUESTION 1
What is the recommended minimum speed at the edge of the cells in an 802.11g network for a good Cisco VoWLAN deployment?

• A. 11 Mb/s
• B. 36 Mb/s
• C. 12 Mb/s
• D. 18 Mb/s

Answer: C

NEW QUESTION 2
After the completion of a site survey with Ekahau Site Survey tool, using the default color palette, it is noted that multiple areas are shown as white on the heat map when viewing 5 GHz signal strength datA. What does this indicate about the signal strength?

• A. The area is below the minimum threshold configured on the tool.
• B. The area is below the detectable level and indicates no RF signal.
• C. The area is below -100 dBm at coverage cell edge.
• D. The area is below -67 dBm at coverage cell edge.

Answer: A

NEW QUESTION 3
When a post-installation audit is performed using the Ekahau Survey tool, which two steps are associated with the passive portion of the audit? (Choose two.)

• A. Check to see if the signal levels on other access points that are heard on the same channel are at least 19 dBm weaker than the access point that you are next to
• B. Survey by SSID to ensure that smooth roaming is taking place
• C. Verify that the real-world network traffic (for example, physical data rate, packet loss, etc.) meets user requirements
• D. When you have completed the post-installation surveys, compare them to the surveys that were performed before the installatio
• E. They should look nearly identical
• F. Verify that user applications are running smoothly over the wireless network

Answer: AD

NEW QUESTION 4
An engineer has performed a post-deployment site survey and noticed that access points were installed in
suboptimal locations due to physical restrictions and obstacles. Which action must the engineer take to resolve this deployment issue?

• A. Set DCAChannel Assignment Method to freeze.
• B. Set all Auto RE parameters to factory default
• C. Set TPC maximum and minimum power levels.
• D. Set static channels on all AP radios.

Answer: C

Explanation: Suspect poor coverage/not enough AP density -- If AP transmit power is already at the maximum, you can enable the lower data rates to allow clients to connect from farther away. This has a negative impact on performance, but it can help the customer understand that additional APs might be necessary. https://www.cisco.com/c/en/us/support/docs/wireless/5500-series-wireless-controllers/116057-site-survey - guidelineswlan-00.html

NEW QUESTION 5
A university is in the process of deploying a wireless network in an auditorium that seats 500 students and supports student laptops. Which deployment methodology should the university implement in the auditorium?

• A. Roaming design model
• B. Location design model
• C. High-density design model
• D. Voice design model

Answer: D

NEW QUESTION 6
You deploy a wireless network for a common area located outside of a student dorm by using patch antennas. Students report weak signals in specific locations of the coverage areA.
Which option is a possible cause of the issue?

• A. neighboring buildings
• B. vehicles
• C. trees
• D. Bluetooth interference

Answer: D

NEW QUESTION 7
An engineer must design a wireless voice network and is auditing the existing configuration. Which two actions must be taken? (Choose two.)

• A. Enable Platinum QoS profile on the SSID
• B. Disable Coverage Hole Detection.
• C. Ensure the switch ports trust DSCP QoS markings
• D. Disable WMM on the QoS tab
• E. Ensure that Client Load Balancing is enabled.

Answer: AC

Explanation: https://mrncciew.com/2012/11/28/understanding-wireless-qos-part-1/

NEW QUESTION 8
If you are calibrating for 2.4 GHz and the site will not be using 802.11 and 802.11b data rates, what should be done to ensure an accurate calibration?

• A. Make sure that the access points have the unused rates disabled.
• B. Make sure that you are using an 802.11b client when calibrating.
• C. Make certain that there are no legacy clients when performing the calibration because they will disrupt the process.
• D. Make sure to use a client that supports both 802.11b/g and 802.11A.

Answer: A

NEW QUESTION 9
Drag and drop the relative AP densities for data, voice and location services from the left to the appropriate categories on the right.

Answer:

Explanation:

NEW QUESTION 10
An engineer must perform a survey where the target client devices range from standard Wi-Fi-equipped laptops, consumer handhelds and tablets, and low power tracking tags limited to 12 mW Tx power. With which setting should the survey AP be configured?

• A. local power 11
• B. local power 5
• C. local power 14
• D. local power 8

Answer: B

NEW QUESTION 11
You are designing a wireless mesh network for an oil refinery. What is the Cisco-recommended model of a Cisco Aironet 1550 Series Outdoor Access Point for this location?

• A. 1552I
• B. 1552CU
• C. 1552E
• D. 1552H

Answer: D

Explanation: Cisco Aironet 1552H Access Point
This ruggedized, outdoor, 802.11n access point is suitable for generic hazardous environments, and does not require a wireless sensor network.
https://www.cisco.com/c/en/us/products/wireless/aironet-1550-series/index.html

NEW QUESTION 12
An engineer is designing the physical infrastructure for an IEEE 802.11ac network. Which power design should the engineer use?

• A. 802.3at PoE+ ports
• B. inline PoE ports
• C. 802.3af PoE ports
• D. 802.3af PoE injectors

Answer: C

NEW QUESTION 13
An engineer is conducting a location readiness test and wants a selected point to be considered location-ready. Which three possible configurations reflect the minimum number of APs needed? (Choose three.)

• A. One AP is resident in each quadrant surrounding the point-in-question
• B. One AP per 1400 s
• C. f
• D. on the map.
• E. Two APs are resident in each quadrant surrounding the point-in-question
• F. our APs are deployed on the floor.
• G. Three APs are within 70 feet (21 meters) of the point-in-question.
• H. Three APs are deployed on the floor.

Answer: ADE

Explanation: A point in a WLAN deployment is location ready if the following are all determined to be true: At least four access points are deployed on the floor.
At least one access point is found to be resident in each quadrant surrounding the point-in-QUESTION NO:
At least one access point residing in each of at least three of the surrounding quadrants is located within 70 feet of the point-in-QUESTION

NEW QUESTION 14
Which three things do you need to consider prior to performing a wireless site survey? (Choose three.)

• A. The time required to acquire any additional infrastructure components.
• B. The time required to survey each potential AP location.
• C. The time required to assess application server locations at the customer facility.
• D. The type of wireless survey tools required to perform the site survey.
• E. The time required to assess customer WLAN density and throughput requirements.
• F. The time required to utilize the design mode in Cisco WCS to prepare a preliminary WLAN design to reduce on-site survey time.

Answer: BDE

NEW QUESTION 15
Which tool in the cisco prime infrastructure can you use to identify whether an existing network can support RFID tags?

• A. Site Survey
• B. Planning Mode
• C. Location Readiness
• D. Voice Readiness

Answer: C

NEW QUESTION 16
You must redesign an existing wireless network that spans multiple floors to support location-based services. Where do you install the access points?

• A. in the elevators
• B. in the perimeter of each floor
• C. in the stairwells of each floor
• D. in the center of each floor

Answer: D